Lithium Battery BMS: Functions, Types and Selection

Every safe lithium battery pack has a BMS, short for Battery Management System. It is only a small electronic board, but without a BMS a lithium pack has no protection at all. This article explains what a BMS does, the main types, and how to choose the right one.
What a BMS does
A BMS works like a guard that constantly watches the inside of the pack.
1. Reads the voltage of every cell. Not just the total pack voltage, but each group of cells connected in series.
2. Disconnects on overcharge. As soon as one cell reaches its upper limit, charging stops.
3. Disconnects on over-discharge. As soon as one cell reaches its lower limit, the load is disconnected so the cell is not damaged.
4. Disconnects on overcurrent or short circuit.
5. Monitors temperature through sensors and disconnects when the pack is too hot, or too cold to charge.
6. Balances the cells, equalizing cell voltages that slowly drift apart.
Why per cell? Because in a series string, the weakest cell reaches its limit first. If only the total voltage is read, one cell can already be overcharged while the total still looks normal.
Types of BMS
By balancing method
Passive balancing. Cells with a higher voltage have a small amount of their energy dissipated as heat until they match the other cells. It is simple and cheap, but the balancing current is small, so it takes a long time to correct a large difference.
Active balancing. Energy is moved from higher cells to lower cells instead of being dissipated. It is faster and more efficient, especially for large-capacity packs, but it costs more.
Whichever type is used, balancing does not replace cell sorting during assembly. Cells whose capacities differ widely will still limit the pack.
By charging path
Common port. Charging and discharging share the same cable path. This is the most common and simplest arrangement.
Separate port. The charge and discharge paths are separate, usually with different current limits. This is useful when the discharge current is much larger than the charge current.
By communication capability
A basic BMS only disconnects and reconnects, without giving any information to the outside.
A smart BMS can be read over Bluetooth in a phone app, or connected to other devices through a data link such as CAN or RS485. In a solar PV system, this data link lets the inverter read the state of charge and current limits directly from the battery.
How to choose a BMS
1. The series cell count must match exactly. A 16S pack needs a 16S BMS. It cannot be approximated.
2. The chemistry must match. LiFePO4 cell voltage limits differ from NMC. A BMS for one chemistry must not be used for another, unless it is configurable and has actually been configured correctly.
3. The continuous current rating must be above the working current. Calculate the largest current the load will draw, then choose a BMS rated above it, with some margin.
4. Consider surge current. A motor starting up, or an inverter being switched on, can draw a large current for a moment. The BMS must handle it, or be fitted with a pre-charge circuit.
5. Decide whether you need a data link. If your inverter or device can read battery data, choose a BMS with a compatible protocol.
6. Number and position of temperature sensors. Large packs should have more than one temperature measuring point.
Common mistakes
- Sense wires connected in the wrong order. The BMS reads voltages in sequence. A wrong order makes the readings and protection incorrect, and can even damage the BMS.
- BMS too small. The pack then often shuts off by itself under heavy load, and the BMS runs hot.
- Wrong chemistry selected. Mismatched voltage limits mean the pack never reaches full charge, or the cells are charged beyond their safe limit.
- Temperature sensor left hanging. The sensor must be attached to a cell, not left in the air.
Need a complete pack with the right BMS?
Cimahi Battery Industry produces prismatic cells and builds custom battery packs in Cimahi, including BMS selection to suit the configuration and load. We describe the installation process in the article battery pack assembly steps.
Contact us on WhatsApp +62 822 6090 4770 or email cimahibattery@gmail.com.
The JBD BMS models we sell, from 4S to 16S, are in the JBD LiFePO4 BMS catalogue.
Need Battery Pack Engineering or Material Testing?
Discuss industrial-grade custom lithium battery assembly or laboratory material testing directly with CBI engineers.
Related Articles & Insights
View All Articles ⟶12V Lithium Battery as a Lead-Acid Replacement
12-volt lithium batteries are increasingly used in place of lead-acid batteries (aki) for emergency lights, UPS units, small solar setups, boats and camping gear.
Electric Bike Battery Drains Fast? 8 Causes to Check
This article covers eight common reasons an electric bike battery drains fast, from tire pressure and dragging brakes to weak cells, sulfation and heat, plus simple checks you can do without opening the battery.